Machined Shawl Collared Cardigan

The original Shawl Collared Cardigan appears in Jo Sharp's Knit Issue 1, which has no machine instructions. I have deviated from the written instructions, stitch count, bands and collar shaping. If anything isn't clear, please obtain your own copy of the book and go from there.

Knit on SK860 midgauge + ribber.
5 x 200G Bendigo Woollen Mills 8ply Highlands in Cinder.
T5 swatch = 22st/28r = 10cm

All bands start with 3 sts on each end, then 11.11 each bed, HP, weight the end stitches to start with, I used a bulldog clip onto the end of a double ended latch tool that came with the machine.

Back
Bands: T2.2/2.2 MB+R; L65..R65 in 2.2 IR rib.
I use long tail cast on and transferred the stitches onto the needles. you need +200 if you do this way, I left the extra dangling until I hung the combs.
work 20R
Body: Transfer all the RB sts to the MB, the 2 group onto the empty needle. (13o sts) reset RC000.
put waist shaping in if you want, but otherwise ->120R reset RC.
Armhole: -6 ev row twice - I thread onto a little piece of scrap. Then -1 (3rd needle onto second, move both in one st) both ends ev alt row 15 times (88st), work to 62R.
Shoulder: set carriages for short row shaping. Reset Russell levers to | both sides.
bring 3 needles on left to D, knit one row, bring 4th needle to D, (4 needles now out of work),
bring 3 needles on right to D, milk the yarn to ensure tight wrap. knit one row, bring 4th needle to D, continue these two actions 4 more times till you have 44 sts COR.
next row is tricky, bring out your 4th needle, STOP, this is the tricky bit don't knit yet, milk the yarn, as you move SLOWLY to take up the wrap BUT YOU MUST NOT LET THE LEFT EDGE OF YOUR CARRIAGE go past your left side wraps, you have to STOP TO DO RESET:
before the edge of the carriage reaches your wrapped stitches, you do reset your Russell lever LEFT SIDE ONLY to ||, this will take up all your stitches on the left, knit to the end of the row, reset right Russell lever to || knit off your final row.
take off all sts however you prefer, mine go onto the circs I keep for this.

Fronts - make two, reversing the shaping on the other one.
L23/R23 work Same as back, with shaping on one side only.
Note: there is no neck shaping.

Sleeves - make two
L23/R23 work bands same as body. RC000
T5 +1 by moving last sts onto next empty needle, pick up the stitch bar under 2nd needle and place on empty needle, both ends every 4th row to 96 sts (RC100)
work to 120RC. reset RC.
Sleeve cap: -6 next (onto scrap), then as before, 3rd onto 2nd and move both in one needle, -1 each end 18 times (RC38), then ev row 15 times to 12 sts and take them off to cast off or cast off around the posts, whichever you prefer.

Bands
T2.2/2.2 MB/RB L16/R16 2.2 IR rib, work to 140 RC, then + 1 ev 6 rows ALL SHAPING IS ON THIS SIDE, then at RC212 or 72 if you did a reset, place a marker, a paper clip, small piece of scrap yarn whatever you choose, this is your shoulder seam and it makes it easier to sew it up - just saying. I put short rows in here, it sits so much better with them.
**Reset RC000 and BOTH carriages to | (all four russell levers) knit one row. COL.
on RIGHT side, pull the (MB) 1x2, 3x2 and (RB) 3x2 needles to D, knit one row
pull out one needle from MB, milk yarn and knit one row.
pull out 3x2 + 3x2 (but one will already be out on the MB- the wrapped stitch), milk, knit.
repeat last 2 rows,** reset ALL Russell levers to || knit to RC36
repeat ** to **
reverse the short rows, wrapping as you go bring needles to B, set side levers to collect them.
knit to RC78 repeat from ** to ** Reset RC000.
-1st ev 6th row to original stitch count = 72RC. reset RC and knit another 140 rows.

Finishing
do 3 needle cast/bind off on shoulders, align your collar with the shoulder seam and join whichever way you like. set in sleeves with linker, machine or darning needle, finish side seams and weave in ends. As you can see, I had help with this.