Tuesday, July 28, 2009

Racked Rib Vest Pattern - Working Notes

Pattern incomplete - still working on it
Back:

C/O 2:2 rib, handle up, FB= 74R:74L, every 3rd needle down, arrange the back bed to match up.
I've been experimenting with the cast on for this rib and this one is:
Attach a weight to the loose end (padlock in my case)
Set needles, blue strippers, rack once left, T2, N/N knit one row,
Change: T4, CX/CX knit one row, set left edge weight (I use yellow/green latch tool with padlock over 2 needles' stitches) knit another row, lock is now at the left (RC3).
Change: rack once right, N/N, carefully knit one row, it will be tight, but goes through. RC000, knit 30 rows.
Change: T5, black strippers.
Rearrange ribs: starting at the centre, 3L:3R have to be on the front bed. 3,2L should be in place, move 1,2R with yellow tool to 2,3R, move 2 stitches from back bed to 1L,1R.
Next move the next 2 FB stitches, one pair each side of your new 6 st set, into the single space on the back bed (new 5 stitch group BB). Continue until you have 6:5 rib all the way, DO THE SAME THING all the way along the front bed. There is an overlap on the same side of the rib configuration, take a good look at which side overlaps (should be on the right) as you will be racking one turn the other way to make an overlap on the other side of the rib on rows 3&4.

The pattern:
Work 2 rows, rack left once, work 2 rows, rack right once. That's all there is to do for the next 150 rows. (except I'm using 50g balls and have to do a couple of joins): I didn't bother with waist shaping, as the ribs should do that for me - not caring if it doesn't either!

Armhole shaping: RC000
Dec sequence, COUNT NEEDLES ON THE FRONT BED, absorb the extra overlap st where it occurs:
-10st x 1 ev 2R (20 st total)
-2 st x 2 ev 2R (4 sts total)
-1 st x 7 ev 2R (10 sts total)
continue to RC 98

Shoulder shaping:
You can do short row shaping if you like OR you can decrease straight from the machine OR you can put them on scrap/decker combs and do a 3 needle cast/bind off. Take your pick.
Dec sequence, COUNT NEEDLES ON THE FRONT BED, absorb the extra overlap st where it occurs:
-6 st x 4 ev 2R
50 sts remaining for neckband.

Left Front:
T4, N/N 2:2 industrial rib, handle down, blue strippers, (+1 FB) L36 / R35 (+1 BB), cast on same of for back, then 30R. RC000.
Change: T5, black strippers.
Rearrange ribs: starting at the right on the front bed. Move 1st and 2nd stitch one needle to the right with yellow tool move 2 stitches from back bed to gap.
Next move the next 2 FB stitches, one pair each side of your new 5 st set, into the single space on the back bed (new 5 stitch group BB). Continue until you have 6:5 rib all the way; the 6 will be on the front bed on the right and the 5 purls will be on the back bed on the left (neck edge), DO THE SAME THING all the way along the front bed. There is an overlap on the same side of the rib configuration, take a good look at which side overlaps (should be on the right) as you will be racking one turn the other way to make an overlap on the other side of the rib on rows every 2nd row. Continue to RC 150.

Armhole and neck shaping: RC000
Dec sequence, COUNT NEEDLES ON THE FRONT BED, absorb the extra overlap st where it occurs: Neck and armhole decreases occur at the same time, the armhole edge is every 2nd row, and the neck every 4th.
Armhole:
-10st x 1 ev 2R (20 st total)
-2 st x 2 ev 2R (4 sts total)
-1 st x 7 ev 2R (10 sts total)
Neck:
-1st x 24, ev 4th row
continue to RC 98

Shoulder shaping:
You can do short row shaping if you like OR you can decrease straight from the machine OR you can put them on scrap/decker combs and do a 3 needle cast/bind off. Take your pick.
Dec sequence, COUNT NEEDLES ON THE FRONT BED, absorb the extra overlap st where it occurs, starting on the armhole edge:
-6 st x 4 ev 2R.

Right Front:
T4, N/N 2:2 industrial rib, handle down, blue strippers, (+1 FB) L36 / R35 (+1 BB), cast on same of for back, then 30R. RC000.
Change: T5, black strippers.
Rearrange ribs: starting at the left on the front bed. Move 1st and 2nd stitch one needle to the left with yellow tool move 2 stitches from back bed to gap.
Next move the next 2 FB stitches, one pair each side of your new 5 st set, into the single space on the back bed (new 5 stitch group BB). Continue until you have rib all the way (from left to right FB has the 6 of the 6:5 and 5 ends on the back bed. There is an overlap on the same side of the rib configuration, take a good look at which side overlaps (should be on the left) as you will be racking one turn the other way to make an overlap on the other side of the rib on rows every 2nd row. Continue to RC 150.

Armhole and neck shaping: RC000
Dec sequence, COUNT NEEDLES ON THE FRONT BED, absorb the extra overlap st where it occurs: Neck and armhole decreases occur at the same time, the armhole edge is every 2nd row, and the neck every 4th.
Armhole:
-10st x 1 ev 2R (20 st total)
-2 st x 2 ev 2R (4 sts total)
-1 st x 7 ev 2R (10 sts total)
Neck:
-1st x 24, ev 4th row
continue to RC 98

Shoulder shaping:
You can do short row shaping if you like OR you can decrease straight from the machine OR you can put them on scrap/decker combs and do a 3 needle cast/bind off. Take your pick.
Dec sequence, COUNT NEEDLES ON THE FRONT BED, absorb the extra overlap st where it occurs, starting on the armhole edge:
-6 st x 4 ev 2R

Armbands:
Make 2: (or do by hand).


Neckband:
Make 2: (or do by hand).

Finishing
Sew seams, and either graft machined bands or cheer as you cast off the bands.

4 comments:

bobbins said...

do you have a finished sweater to show us yet? After the teaser image to show us the beautiful rib design I am eager to see the finished object!
Tobey

ozlorna said...

It's back to the drawing board, I'm afraid! The finished fabric was a little too tight, so I've ripped it all back and remake this one on a looser stitch tension.

I may keep these notes as a draft for one of my thinner yarns.

bobbins said...

Good Idea, no sense having a too-tight sweater. A bit sad it had to be ripped out, though. At least you will have this set of instructions to work from for the next version!
Tobey

ozlorna said...

That's definitely The Plan! LOL! I should have another go at it next week.